A chainwire fence is not a product. It is a family of fences that ranges from a $38 per metre garden boundary to a $260 per metre secure perimeter, and the only thing that tells you which one you are buying is the specification.
Four numbers do most of the work: height, mesh aperture, wire gauge and post size. Get those four right and the rest of the fence follows. Get them wrong and you will either overpay for a fence you did not need or, more commonly, underspecify and replace it inside five years.
This guide walks through every number a chainwire quote should contain, what each one controls and how to decide yours. At the end there is a one-paragraph template you can paste into an email so every contractor quotes the same fence.
If you are still getting your head around the product itself, start with what a chainwire fence actually is, because chainwire, chain link, chain mesh and cyclone fencing are all the same thing under different names.
A note on units. Height and mesh are in millimetres. Wire gauge is the wire diameter in millimetres, not an old gauge number, though some suppliers still quote both. Posts are sized in NB, nominal bore, which is a pipe sizing convention: 40NB is roughly 48mm outside diameter, not 40mm. Contractors use these interchangeably and it causes real confusion.
What parts of a chainwire fence actually get specified?
Ten components make up a complete specification, and four of them drive almost all of the cost and performance. Everything else on the drawing follows from those four: a taller fence needs a bigger post, a bigger post needs a deeper footing, and finer mesh on heavier wire needs tighter post spacing to carry the extra weight and tension.
| Part | What it controls | Typical options |
|---|---|---|
| Height | What the fence stops, post size, footing depth, whether you need approval | 900mm to 4.2m |
| Mesh aperture | What fits through, how hard it is to climb, fabric cost per square metre | 25mm to 60mm |
| Wire gauge | Cut resistance, lifespan, weight of the fabric | 2.0mm to 4.0mm |
| Post size | Whether the frame holds the mesh in tension | 32NB to 80NB |
| Post spacing | Whether the mesh bellies between posts | 2.0m to 4.0m |
| Coating | How long the fence lasts before rust wins | Galv before weaving, galv after, heavy galv, PVC |
| Selvedge | Whether the edges are safe to touch | Knuckled or barbed |
| Rails and tension wire | Straightness of the line, security at the base | Top rail, mid rail, bottom rail, tension wire |
| Footings | Whether the fence stays upright | Depth and diameter by height and soil |
| Bracing | Whether terminal posts resist the strain | Diagonal brace, strut, larger footing |
How tall should a chainwire fence be?
Pick the height from what the fence has to stop, not from a catalogue. Height drives post size, footing depth, rail count and whether you need planning approval, so it is the first number you should settle.
| Height | Stops | Does not stop | Standard stock |
|---|---|---|---|
| 900mm | Small dogs, garden edges, defining a line | Anyone, anything | Yes |
| 1.2m | Toddlers, most dogs, casual trespass | A determined adult, a jumping dog | Yes |
| 1.5m | Most dogs, stock, casual entry | A climber | Yes |
| 1.8m | Casual climbing, stock, the great majority of intrusions | A prepared climber | Yes, most common |
| 2.1m | Opportunistic climbing without equipment | Someone with a ladder or an accomplice | Yes |
| 2.4m | Climbing without aids, ball escape at low speed | A thrown object, a lofted ball | Yes |
| 3.0m | Nearly all unaided climbing, most ball escape | A high lob, a vehicle | Yes |
| 3.6m to 4.2m | Tennis lobs, cricket, golf strays | Nothing you will meet on a sports site | Made to order |
Where the NSW approval line falls
In NSW a side or rear boundary fence generally needs no planning approval up to 1.8 metres, and a fence along a road boundary, which includes the front boundary and the street-side boundary of a corner block, is capped at 1.2 metres. That is why 1.8m and 1.2m are the two most quoted residential heights in Sydney. If your project needs 2.1m or more on a residential boundary, factor approval time into the program and check your council’s LEP and DCP first, because heritage, bushfire, flood and foreshore areas tighten these controls. For the zoning-by-zoning detail, read our guide to chainwire fence height in NSW and when council approval is required.
Stock heights cost less, and not by a little
Chainwire mesh is manufactured in standard roll heights: 900mm, 1200mm, 1500mm, 1800mm, 2100mm, 2400mm and 3000mm. Asking for 2000mm means either cutting a 2100mm roll, which wastes 100mm of mesh across the whole run and leaves a cut selvedge that has to be re-knuckled or left sharp, or a special order. Specify a stock height unless there is a good reason not to.
Height is measured from where, exactly?
On flat ground this is obvious. On a slope it is not. Agree with your contractor whether the stated height is measured at the post, at the lowest point of each bay, or as a nominal fabric height. The difference on a steep raked run can be 200mm, and on a childcare or pool-adjacent site that gap is a compliance problem rather than an aesthetic one. Fencing on sloping ground is where this catches people out most often.
What mesh aperture do you need?
Aperture, properly called pitch, is the size of the diamond measured diagonally across it. AS 1725.1 sets 50mm nominal pitch as the maximum for chain-link fabric, so 50mm is the coarsest mesh the standard recognises.
This one number decides what fits through the fence, how hard it is to climb, and how much wire you are paying for per square metre.
| Aperture | Also called | What it does | Where it is specified |
|---|---|---|---|
| 25mm | Anti-climb, high security | No finger or toe hold, very hard to cut through quickly | Substations, detention, data centres, utility compounds |
| 40mm | Fine mesh | Resists toe holds, contains small animals and balls | Childcare, animal enclosures, netball and basketball courts |
| 45mm | Court mesh | The tennis and sports standard, balls cannot pass | Tennis courts, multi-use courts, school ball courts |
| 50mm | Standard | General purpose, climbable but contains people and dogs | Residential boundaries, schools, general commercial |
| 60mm | Economy, stock mesh | Boundary definition, stock containment | Rural runs, long industrial perimeters, budget jobs |
Finer mesh costs more because it is more wire
Halving the aperture roughly doubles the metres of wire in a square metre of fabric. That is why 25mm mesh is not a small upgrade from 50mm, it is close to a doubling of the fabric cost, and it is also substantially heavier, which pushes post spacing in and footings deeper. Budget $10 to $35 per metre more as you go finer.
The climbing trade-off nobody mentions
Standard 50mm mesh is climbable by any reasonably fit adult, because a boot toe fits the diamond. People assume that adding height fixes this. It does not fix it anywhere near as efficiently as reducing aperture.
Going from 1.8m to 2.4m at 50mm adds maybe eight seconds to a climb. Going from 50mm to 25mm at the same height usually makes an unaided climb impractical. If security is the goal, spend the money on aperture before you spend it on height.
For courts, the ball dictates the mesh
A tennis ball is about 67mm in diameter, so it cannot pass 50mm mesh, but it will deform through and jam in it, which damages the fabric over time and looks terrible. 45mm is the practical court standard because the ball rebounds cleanly rather than wedging. A netball is far larger, so 50mm is fine, but courts used for multiple sports should be specified to the smallest ball in use. We cover the court-specific side in why proper sports court fencing matters.
What wire gauge should you specify?
Gauge is the diameter of each individual wire in millimetres. It is the single most common omission in a chainwire quote, and the single easiest place for a contractor to save money without you noticing, because 2.0mm and 3.15mm mesh look almost identical from three metres away.
| Gauge | Relative cross-section | Resists | Typical application |
|---|---|---|---|
| 2.0mm | 0.64 | Light contact, garden use | Budget residential, temporary, garden and pet enclosures |
| 2.5mm | 1.00 (baseline) | Leaning, climbing, general knocks | Standard residential and light commercial |
| 3.15mm | 1.59 | Bolt cutters slow markedly, vehicle brush contact | Schools, commercial yards, sports courts |
| 4.0mm | 2.56 | Serious attack, forklift and plant contact | Industrial, utility, high-security perimeters |
One caveat on that table. AS 1725.1 recognises only two core wire diameters for chain-link fabric: 2.50mm light duty and 3.15mm heavy duty. The 2.0mm and 4.0mm products are sold in Australia and have their uses, but neither complies with AS 1725, so do not specify them on a job where the standard is cited.
Why 3.15mm is the real security threshold
The step from 2.5mm to 3.15mm is a 59 percent increase in steel cross-section. In practice that is the difference between mesh a pair of hand bolt cutters goes through in a few seconds and mesh that needs a long-handled cutter and visible effort. For any site where an intruder is a genuine risk rather than a theoretical one, 3.15mm is the floor and 4.0mm is the answer if the budget allows.
Gauge also decides how the fence ages
Galvanising is applied as a coating of a given mass per square metre. A thicker wire has proportionally less surface area for its volume, so the same coating protects it for longer in real terms, and it has more steel to lose before it fails. A 2.0mm fence in coastal Sydney can be structurally compromised in under a decade. A 3.15mm fence in the same spot will still be sound when it is cosmetically ugly. Our guide to the best materials for long-lasting chainwire fences goes through the corrosion side in detail.
Specify core diameter, not finished diameter
With PVC coated mesh there are two diameters: the steel core and the finished wire including the coating. A supplier quoting “3.5mm PVC coated” may mean a 2.5mm core with a 0.5mm coating all round. The core is what carries load. Always specify it as, for example, “2.5mm core, 3.5mm finished”. This is a genuinely common source of disputes.
What coating and selvedge does the job need?
Coating decides how long the fence lasts. Selvedge decides whether it is safe to put children next to it. They are separate specifications and both get skipped.
| Coating | What it is | Sydney lifespan | Cost effect |
|---|---|---|---|
| Galvanised before weaving | Wire is galvanised, then woven; cut edges are bare | 10 to 18 years inland | Cheapest |
| Galvanised after weaving | Fabric is woven, then dipped; the knuckles are coated too | 18 to 28 years inland | +$3 to $8 per metre |
| Heavy galvanised | Higher zinc mass per square metre | 20 to 30 years inland | +$4 to $10 per metre |
| PVC coated over galvanised | Plastic sheath over a galvanised core | 20 to 30 years including coastal | +$8 to $20 per metre |
Galvanising after weaving matters more than people expect
In the before-weaving process, every point where the wire was bent into a knuckle has stressed and thinned the zinc, and those knuckles are exactly where rust starts. On the coast, specify after-weaving galvanising or PVC. If you are weighing up finishes, black chainwire vs galvanised covers how each one holds up in Sydney conditions.
Selvedge: knuckled or barbed
Selvedge is how the mesh is finished at the top and bottom edge, where the wire turns back on itself.
Knuckled means the wire ends are bent into a smooth closed loop. Safe to touch. This is the only acceptable finish on any edge a person can reach.
Barbed, sometimes called twisted or cut selvedge, leaves the wire ends as sharp protruding points. It is a deterrent finish.
The usual specification for a commercial perimeter is knuckled bottom, barbed top. That is safe at ground level and unpleasant to grab at the top. For schools, childcare, parks, sports courts and any residential fence, specify knuckled both edges, full stop. If you are adding a topping, check what is actually allowed with barbed or razor wire in NSW first.
The cut edge problem
When a roll is cut to height or trimmed around a gate or an obstruction, the cut leaves bare steel and, usually, sharp points. A good contractor re-knuckles or caps these. A cheap one leaves them. On a school fence, a row of cut wire ends at child height is both an injury risk and a defect you can ask to have rectified. Put “all cut edges to be knuckled or capped” in your specification and it becomes a contract term rather than a request.
What posts, spacing and rails hold the fence up?
The mesh is the cheap part. The frame is what holds it in tension, and almost every chainwire fence that fails does so at the frame rather than the fabric.
Post sizes
Posts are specified in NB, nominal bore. The number is a pipe convention, not an outside diameter, so 40NB is about 48mm across and 50NB about 60mm.
| Post size | Outside diameter | Line post up to | End, corner and gate post up to |
|---|---|---|---|
| 32NB | about 42mm | 1.2m | 900mm |
| 40NB | about 48mm | 1.8m | 1.5m |
| 50NB | about 60mm | 2.4m | 1.8m |
| 65NB | about 76mm | 3.0m | 2.4m |
| 80NB | about 89mm | 3.6m and above | 3.0m |
Note the last two columns. An end, corner or gate post always steps up at least one size above the line post, because it carries the tension of the whole run rather than just supporting the fabric. A quote with one post size listed for the entire job is a quote that has not thought about this.
Spacing
Standard line post spacing is 3.0m centres. Wider than that and the mesh bellies between posts under its own weight. Tighter than that is specified when the fabric is heavy, the fence is tall, or wind load is a factor.
- 4.0m centres: light 1.2m fences on flat ground only
- 3.0m centres: the general standard for 1.5m to 2.4m
- 2.5m centres: 3.0m and taller, 25mm mesh, 4.0mm wire, exposed or windy sites
- 2.0m centres: shade cloth or privacy slats fitted, because the fence becomes a sail
That last point catches people out constantly. Adding privacy slats or shade cloth to an existing chainwire fence can triple its wind load. Fences designed at 3.0m centres for open mesh will lean or fail once they are screened. There is more on this in how far apart fence posts should be in Australia.
Rails and tension wire
- Top rail, usually 32NB, threaded through the top of the mesh and clipped to posts. It keeps the line straight and stops the top edge being pushed down. Specify it on anything 1.5m and over.
- Mid rail, on fences 2.4m and taller, stops the fabric flexing in the middle of its height.
- Bottom tension wire, a single strained wire woven through the bottom of the mesh and anchored at end posts. The cheap option, and adequate for most residential work.
- Bottom rail, a proper pipe rail instead of tension wire. Stops the mesh being lifted and crawled under. Specify this at schools, childcare, dog enclosures and anywhere stock is held.
Straining and bracing
Chainwire is a tension structure. The mesh is pulled tight between straining posts, and the straining post has to resist that pull. On a straight run, strainers go at each end and at intervals of roughly 30 to 50 metres.
Each strainer needs either a diagonal brace back to the first line post, a horizontal strut with a tension wire, or a substantially larger footing. A fence strained against unbraced end posts will pull those posts inward and the whole run will sag within months. Ask how your end posts are braced and you will immediately learn how seriously the contractor takes their work. Unbraced terminals are also one of the most common reasons a chain wire fence ends up sagging.
How deep do chainwire footings need to be?
A rule of thumb used across the trade is that a post should be buried roughly a third of its above-ground height, with more for strainers and gate posts. The table below is a reasonable starting specification for stable Sydney soils.
| Fence height | Line post hole | End or strainer post hole | Gate post hole |
|---|---|---|---|
| 1.2m | 400mm deep, 250mm wide | 500mm deep, 300mm wide | 600mm deep, 350mm wide |
| 1.8m | 450mm deep, 300mm wide | 600mm deep, 400mm wide | 750mm deep, 450mm wide |
| 2.4m | 600mm deep, 350mm wide | 750mm deep, 450mm wide | 900mm deep, 500mm wide |
| 3.0m | 750mm deep, 400mm wide | 900mm deep, 500mm wide | 1000mm deep, 600mm wide |
All holes concreted, with the concrete crowned above ground level and sloped away so water runs off the post rather than pooling at its base.
Sydney soils change the answer
- Reactive clay, common across Western Sydney, Blacktown, Penrith and the Hills, swells when wet and shrinks when dry. Shallow footings get heaved and the fence leans. Add 100mm to the depths above.
- Sand, on the Northern Beaches and parts of the eastern coastal strip, gives very little side resistance. Widen the hole rather than deepening it, and consider a belled base.
- Sandstone, across the Eastern Suburbs, Lower North Shore and parts of the Shire, is the opposite problem. You cannot dig the specified hole, so posts get chemically anchored or set into a drilled socket. This is a legitimate and durable solution, but it should be priced and described, not improvised on the day.
- Fill, common on former industrial sites and newer estates, may not be competent at any practical depth. If the site is fill, get advice before specifying footings off a table.
For the depth side in more detail, see how deep fence posts should be dug across Australia, and for rock and slab situations, chainwire fencing on concrete.
Gate posts are a different calculation
A gate post carries a cantilevered load that changes every time the gate swings, plus the shock of it being slammed. For double gates over 4 metres, the standard practice is a substantially oversized post, a footing at least twice the volume of a line post footing, and in many cases a concrete thrust block or a tie back to the adjacent line post. If a gate drops out of alignment within the first year, the footing is almost always the cause. Our chainwire gate guide covers sizing and automation.
How do you read a chainwire spec line?
A complete specification looks like a string of abbreviations. Here is a real one, decoded piece by piece.
| Fragment | Means |
|---|---|
| 1800 | Fabric height in millimetres |
| 50 | Mesh aperture in millimetres, across the flats |
| 2.5 | Wire diameter in millimetres |
| GAW | Galvanised after weaving, so the knuckles are coated |
| knuckled both edges | Smooth closed loops top and bottom, no sharp points |
| 40NB line posts at 3.0m crs | Line posts of 40 nominal bore at 3.0 metre centres |
| 50NB end and corner posts braced | Heavier posts at terminations, with bracing to resist tension |
| 32NB top rail | A pipe rail threaded along the top of the fabric |
| 2.5mm bottom tension wire | A strained wire along the bottom edge |
| 450 x 300 | Footing depth and diameter in millimetres |
| galv fittings | Caps, rail ends, tension bars, bands and tie wire all galvanised |
What is still missing from that line
Even a spec that complete leaves four things unstated that are worth adding: the number and location of strainer posts, the coating standard for the fittings, what happens at cut edges, and how height is measured on slope. On a tender document for a school or a commercial site, add those four and you have removed almost all the room for argument.
A security variant for comparison
Same product category, roughly three times the price, and a completely different fence. That gap is the reason specification matters more than the per metre rate.
What specification suits each application?
These are starting points, not final answers. Use them as the first draft of your brief and adjust for site, exposure and council requirements.
| Application | Height | Mesh | Wire | Coating | Line post | Bottom |
|---|---|---|---|---|---|---|
| Residential side or rear boundary | 1.8m | 50mm | 2.5mm | Galv after weaving, or black PVC on the coast | 40NB at 3.0m | Tension wire |
| Residential front boundary | 1.2m | 50mm | 2.5mm | Black PVC | 32NB at 3.0m | Tension wire |
| Dog run or animal enclosure | 1.8m | 40mm | 2.5mm | Galv after weaving | 40NB at 3.0m | Bottom rail, plus dig guard |
| Childcare perimeter | 1.8m | 40mm | 2.5mm | PVC, knuckled both edges | 40NB at 3.0m | Bottom rail |
| School boundary | 2.1m | 50mm | 3.15mm | Galv after weaving or PVC | 50NB at 3.0m | Bottom rail |
| Tennis court | 2.7m sides, 3.6m to 4.2m ends | 45mm | 2.5mm | Black PVC | 50NB at 3.0m | Bottom rail |
| Netball or basketball court | 2.4m to 3.0m | 40mm or 50mm | 2.5mm | Black or green PVC | 50NB at 3.0m | Bottom rail |
| Council park or reserve | 1.8m to 2.1m | 50mm | 3.15mm | Galv after weaving | 50NB at 3.0m | Tension wire |
| Commercial yard | 2.1m to 2.4m | 50mm | 3.15mm | Heavy galv | 50NB at 3.0m | Tension wire |
| Warehouse or depot perimeter | 2.4m plus barbed arms | 50mm | 3.15mm | Heavy galv | 50NB at 3.0m | Bottom rail or plinth |
| Substation or utility compound | 2.4m to 3.0m plus arms | 25mm | 4.0mm | Heavy galv | 65NB at 2.5m | Concrete plinth |
| Construction site, permanent | 2.1m to 2.4m | 50mm | 3.15mm | Galv | 50NB at 3.0m | Tension wire |
| Construction site, temporary | 2.1m panels | 60mm | 3.15mm | Galv | Panel feet, braced | Not applicable, free standing |
Three modifiers that override the table
- Coastal exposure. Anywhere within a few kilometres of the ocean or a tidal waterway, step the coating up to PVC or heavy galvanised after weaving, regardless of what the table says.
- Screening. If slats, shade cloth or scrim will ever be fitted, drop post spacing to 2.0m and step the post size up one. The wind load changes the structure, not just the appearance.
- Public frontage. Any fence facing a footpath, playground or public space takes knuckled selvedge both edges and no barbed topping below 2.4m, irrespective of the security case.
Which Australian Standards apply to chainwire?
Chainwire has its own standard, and most people specifying it have never read it. AS 1725 was expanded in September 2010 from a single document into five parts, each covering a different application. Citing the right part in your brief is the fastest way to get comparable, compliant quotes.
| Standard | Covers |
|---|---|
| AS 1725.1 | Security fences and gates, general requirements |
| AS 1725.2 | Tennis court fencing, commercial |
| AS 1725.3 | Tennis court fencing, private and residential |
| AS 1725.4 | Cricket net fencing enclosures |
| AS 1725.5 | Sports ground fencing |
| AS 4687 | Temporary fencing and hoardings |
| AS 2423 | Coated steel wire fencing products |
| AS 4312 | Atmospheric corrosivity zones in Australia, which drives coating choice |
| AS 1926.1 | Swimming pool safety barriers, where the fence is also a pool barrier |
What AS 1725.1 actually requires
The general requirements are more prescriptive than most quotes suggest.
- Terminal posts, meaning end, corner and gate posts, have a minimum of DN50 medium grade galvanised pipe, which is 3.6mm wall thickness.
- Intermediate posts have a minimum of DN40, in medium, light or extra-light grade.
- Core wire diameter for chain-link fabric is either 2.50mm light duty or 3.15mm heavy duty. Those are the two options the standard recognises.
- Maximum pitch of the diamond is 50mm nominal, measured diagonally across the diamond.
- Maximum post spacing is 3330mm centres.
- Lacing wire must be 2.00mm core. The thinner 1.57mm tie wire may only be used to secure fabric to horizontal cable wires.
- Standard Galvanised (SG) W02Z wire does not meet the minimum standard for any part of AS 1725. Heavy Galvanised W10Z, zinc-aluminium alloy W05Z5A and PVC over a base coating of at least W02Z are all accepted.
That last point is the one worth remembering. If a quote says “galvanised chainwire” with no grade, it may well be SG wire, which is below the standard for every application AS 1725 covers.
The sports parts are stricter again
| Application | Fabric minimum | Post spacing maximum | Notes |
|---|---|---|---|
| Commercial tennis (1725.2) | 45mm pitch x 3.15mm heavy duty | 3330mm | Intermediate posts min DN50, corner posts min DN80; extra light pipe does not comply |
| Residential tennis (1725.3) | 45mm pitch x 3.15mm or 2.50mm | 3330mm | Corner posts min DN65 |
| Cricket nets (1725.4) | 3.15mm, 40mm pitch behind the nets, 50mm to sides and roof | 3000mm | Top and bottom rail mandatory; end posts min DN80 |
| Sports ground (1725.5) | 50mm pitch x 3.15mm for types 1 to 4 | 2400mm | Five durability types; 2.50mm fabric only permitted for type 5 |
Two details from the standards worth stealing
Cricket nets put fabric on both faces of internal dividing fences. The reason is that an exposed post can rebound a ball straight back at the batter or bowler. It is a good principle anywhere a ball meets a fence at speed.
Commercial tennis fencing makes no allowance for signage, windbreak or creepers. If you intend to attach any of those, the standard directs you to get an engineer’s design for the fence members and backstays, based on the wind category. This is the formal version of the point made earlier about screening and wind load.
Can chainwire be a swimming pool barrier?
Usually not. Chainwire is generally unsuitable as a swimming pool barrier because standard 50mm mesh gives a climbable foothold, and pool barriers in NSW must comply with AS 1926.1, with the applicable version depending on when the pool was built. Every pool and spa in NSW must also be on the Swimming Pool Register. Do not assume a boundary chainwire fence can double as a pool barrier without a certifier confirming it.
What are the specification mistakes that cost the most?
Eight mistakes come up again and again, and each one has a real price attached. Seven of them share the same root cause.
| Mistake | What goes wrong | Cost to fix later |
|---|---|---|
| Omitting wire gauge | You get 2.0mm when you assumed 2.5mm, and it sags and cuts easily | Re-mesh the whole run, roughly 55 percent of a new fence |
| Omitting the galvanising grade | SG wire fails AS 1725 and rusts years early | Full replacement, 100 percent |
| One post size for the whole job | Unbraced terminal posts pull in, the run sags permanently | Replace terminals and restrain, $400 to $900 per terminal |
| Barbed selvedge on a public-facing fence | Injury risk, complaints, likely rectification order | Re-knuckle or replace the top edge, $25 to $50 per metre |
| Adding slats or shade cloth later | Wind load triples, posts lean or snap | Reduce spacing and resize posts, often cheaper to rebuild |
| Non-standard height | Cut selvedge, wasted mesh, sharp edges, long lead time | Nothing fixable, you just paid more for a worse fence |
| Gate posts the same size as line posts | Gates drop, leaves stop meeting, drop bolt misses | New gate posts and footings, $800 to $2,500 per gate |
| No footing specification | Shallow holes, fence leans after one wet season | Re-set posts, $200 to $400 per post |
The pattern behind all eight
Seven of these eight come from the same root cause, which is specifying the fence by what it looks like rather than by what it is made of. Chainwire is unusual among fence types in that a $45 per metre version and a $160 per metre version are visually near-identical at normal viewing distance. Timber and Colorbond give you obvious visual cues when corners have been cut. Chainwire does not. The specification is the only protection you have.
The one that is not a specification failure
The slats-and-shade-cloth problem is different. It is usually a fence that was correctly specified for its original purpose and then changed. The lesson is to decide at specification time whether the fence will ever be screened, even years later, and design the frame for the screened case. The extra cost of 2.0m post spacing on a fence that may never be slatted is a few hundred dollars. The cost of discovering the problem in a storm is the fence.
How do you put all of this in one paragraph?
Copy this into an email or a tender document. Any contractor quoting against it is quoting against the same fence as everyone else.
Frequently asked questions
What is the standard chainwire fence specification in Australia?
For general use, 1800mm high, 50mm pitch, 2.50mm core wire, galvanised, with 40NB line posts at 3.0m centres, 50NB terminal posts, a 32NB top rail and a bottom tension wire. That is the AS 1725.1 light duty baseline and it covers most residential and light commercial work.
What does NB mean on a fence post?
Nominal bore, a pipe sizing convention. The number is not the outside diameter. 32NB is about 42mm across, 40NB about 48mm, 50NB about 60mm, 65NB about 76mm and 80NB about 89mm. Some suppliers use DN, which means the same thing.
What is the difference between chainwire, chain mesh, chain link and cyclone fencing?
Nothing. They are regional and historical names for the same product. Cyclone was a brand name that became generic in Australia. The standards call it chain-link fabric fencing.
What mesh size should I use for a tennis court?
45mm pitch on 3.15mm heavy duty wire is the minimum AS 1725.2 specifies for commercial courts. Residential courts under AS 1725.3 may use 45mm pitch on either 3.15mm or 2.50mm wire.
What is the maximum post spacing for a chainwire fence?
3330mm centres under AS 1725.1, reducing to 3000mm for cricket net enclosures and 2400mm for sports ground fencing. Most contractors work to 3.0m as a practical standard.
Should selvedge be knuckled or barbed?
Knuckled on both edges for anything a person can reach, including all residential, school, childcare and park fencing. Knuckled bottom with barbed top is the normal commercial security specification.
Does galvanising before or after weaving matter?
Yes, considerably. Galvanising after weaving coats the knuckles, which is exactly where rust starts. In coastal Sydney it can be the difference between twelve years and twenty-five.
Can chainwire be a swimming pool barrier?
Usually not, because standard mesh is climbable. Pool barriers in NSW must comply with AS 1926.1 and the pool must be on the Swimming Pool Register. Get a certifier to confirm before relying on an existing fence.
Getting the specification right before you get a quote
Chainwire is a tension structure built from a handful of numbers, and every one of them is checkable before a single post goes in the ground. A quote that does not state height, aperture, gauge, post size and footing is not a cheaper quote, it is a quote for a different fence.
Longain Fencing supplies and installs chainwire fencing across Sydney, from residential boundaries through to schools, sports courts and commercial perimeters. Send us the spec you want quoted, or ask us to work through yours, and we will price the fence you actually asked for. See how our chainwire fence installation in Sydney works, or get in touch for a free quote.